How To Build A Bathroom Organizer

Steps for building a bathroom organizer:

Step 1: Prep the frame pieces Download our cut list above. Cut all the pieces to size. Using a pocket hole jig and drill/driver fitted with a pocket hole drill bit (both set to a ¾-inch depth), create two pocket holes in each end of the Frame’s 1 x 2 Front, Back and Side pieces. Step 2: Prep the plywood shelves Using a pocket hole jig and drill/driver fitted with a pocket hole drill bit (both set to a ½-inch depth), create three pocket holes along the side edges of each plywood shelf. Step 3: Mark the height of the shelves Stack the Frame Legs side-by-side. Mark the height of the top edge of the Sides Pieces at 3-inches, 26-inches, and 39-inches. (Note: The fourth Side piece sets flush with the top edge of the Legs.) Step 4: Build the frame sides Lay two 1 x 2 Legs parallel on the work surface with four 1 x 2 Side pieces between them. Position the Side pieces below each marked line. Apply a small amount of wood glue to the ends of the Side pieces. (Tip: Use a face clamp to keep the faces flush during assembly.) Using a drill/driver and 1¼-inch pocket hole screws, assemble the parts. Repeat to attach the remaining Legs and Side pieces. Step 5: Attach the front and back pieces Stand the 1 x 2 Front and Back pieces level with the top and bottom Side pieces. Position the pieces so that their pocket holes face the same direction (toward the back) of the assembly. Using the method used to attach the Side pieces, attach the 1 x 2 Front and Back pieces. Step 6: Assemble the frame Sandwich the Front and Back pieces between the assembled sides of the Frame. Using wood glue and 1¼” pocket hole screws, attach the Front and Back boards to the remaining Legs. Step 7: Attach the shelves Place the Frame upside down on the work surface. Position the Shelves flush with the surface of the Side pieces. Using a drill/driver, drive 1-inch pocket hole screws through the Shelves and into the Sides pieces. Step 8: Prep the frame for stain Sand the parts, and then wipe away any dust with a lint-free cloth. Step 9: Stain the frame Using a lint-free cloth, wipe on a coat of stain in the direction on the grain. I’m using a Varathane color called Dark Walnut. Let the stain set for two to three minutes. Wipe away the excess stain with a lint-free cloth, and let dry for at least an hour. Step 10: Apply the polyurethane Using a synthetic bristle brush, apply a liberal coat of Varathane Triple-Thick Polyurethane. Once coated, pull the brush across the edges at a 45-degree angle to tip-off the finish and prevent drips. Step 11: Cut the hamper hole It’s now time to assemble the hamper. Locate the 1 x 2 Hamper Door Top. Mark a 4-inch-wide-by-¾-inch-tall outline centered on bottom edge of the pieces. If desired, angle the edges of the cutout at 45 degrees. Using a jigsaw, cut out the handle. Step 12: Assemble the hamper door frame Using a pocket hole jig and drill/driver fitted with a pocket hole drill bit (both set to a ¾-inch depth), create two pocket holes in each end of the Door’s 1 x 2 Side pieces. Apply glue to the ends of the Side pieces. Sandwich the Sides between the Top and Bottom. (Tip: Use a face clamp to keep the faces flush during assembly.) Using a drill/driver and 1¼-inch pocket hole screws, assemble the door’s frame. Step 13: Attach the slats Create two pocket holes in each end of the Door’s 1 x 2 Slats. Position the Slats between the Sides, using two paint sticks to create even spacing. Using a drill/driver and 1¼-inch pocket hole screws, assemble the parts. Step 14: Attach the hamper sides Using a pocket hole jig and drill/driver fitted with a pocket hole drill bit (both set to a ½-inch depth), create three pocket holes along one side edge of the hamper’s plywood Sides. Apply a bead of glue along the edge with the pocket holes. Stand the side on edge on the backside of the Door, flush with the bottom edge and ¾-inch from the side edge of the door, with the pocket holes facing inward. Using a drill/driver, drive 1-inch pocket hole screws through the Side and into the Door. Repeat to attach the remaining Side to the Door. Step 15: Attach the hamper base and back Drill two pocket holes along each side of the Hamper Base, three pocket holes along the side edges of the Hamper Back. Using wood glue and 1-inch pocket hole screws, attach the Base, and then the Back of the Hamper between the Sides. Step 16: Paint the hamper Sand the hamper, and fill pocket holes with wood filler, if desired. Apply two coats of paint to the hamper. (Tip: Run a sponge brush between the slats to coat the gaps and prevent drips.) Step 17: Install the hamper Using a drill/driver, install a piano hinge flush with the front edge of the Frame’s lower Front Piece. Prop the base of the hamper up on a scrap block. Position the hinge on the underside of the hamper, flush with its front edge. Secure the hinge with screws. Tilt the hamper closed. Prevent the hamper from tilting too far open with a chain (attached to the side of the hamper and the frame), if desired.

Materials:

Varathane® Premium Fast Dry Wood Stain Varathane® Triple Thick Polyurethane Rust-Oleum® Chalked Paint in White Linen (5) 1 x 2 x 8 Boards (2) ½” x 2”x 4” Plywood 1¼” and 1” Pocket Screws Wood Glue

Tools: